Báo cháy thông thường
-
Còi + đèn chớp (outdoor) SB112F
Còi + đèn chớp báo cháy lắp đặt ngoài nhà (outdoor)
Nguồn cấp: 16-30V
Tổng dòng khi có trạng thái báo động: 80mA, 24V
Âm lượng ở khoảng cách 30cm: 112dB
Tần số: 2.9-4 kHz
Tần số chớp của đèn flash: 2Hz 0.6W
Liên hệ -
Card kết nối BMS
Xem CatalogeCard kết nối BMS của Unipos sử dụng giao thức RS-232 và RS-485 để kết nối các tủ báo cháy địa chỉ dòng IFS7000 với các thiết bị của bên thứ 3 (thirdparty) theo chuẩn Modbus (các thiết bị lập trình PLC).
A Modbus Map with the UniPOS IFS7000 Detectors statuses, FPE statuses, FAD statuses are available in Modbus Input registers and Basic commands to control the IFS7000 system can be executed through Modbus Holding registers.
Module sử dụng cả kiểu kết nối vật lý và logic:
- Khi kết nối vật lý, card này truyền kết nối RS232 và RS485, thích hợp sử dụng trong môi trường có độ nhiễu cao.
- Khi kết nối logic, truyền tín hiệu theo giao thức UniTalk của Unipos đến giao thức ModBus của hệ thống BMS;Technical data
Interfaces: RS232 (UniPOS UniTALK protocol), RS485 (Modbus protocol)
Number of 7002 panels: Maximum 14 pcs. in Network
Power Supply: (12-30)Vdc
Current consumption: up to 60mA
Operating temperature range: minus 5 to plus 40 degrees
Relative humidity: (93+/- 3)% at 40 degrees
Dimensions: (130x110x22) mm
Tham khảo thêm các thiết bị báo cháy tự động liên quan: Tủ trung tâm báo cháy địa chỉ, đầu báo khói địa chỉ, đầu báo nhiệt địa chỉ, module giám sát, module điều khiển, Module định địa chỉ cho đầu báo thường, nút nhấn địa chỉ, chuông báo cháy, đèn báo cháy ngoài nhà Unipos, tủ hiển thị phụ UniposLiên hệ -
Đầu báo khói độ nhạy cao
Đầu báo khói độ nhạy cao YKB-02 được UNIPOS thiết kế để phát hiện khói trong luồng không khí trong ống thông gió.
YKB-02K là đầu báo hệ thường, còn YKB-02A là đầu báo hệ địa chỉ.
Duct smoke detector YKB-02 is designed to detect the presence of smoke in airstream of ductwork sections or ventilating compartments by the smoke detector mounted in it.Depending on the type of the fire detector mounted , the duct smoke detector is produced in two variants – for Conventional Fire Alarm Systems (YKB-02K) and for Addressable Fire Alarm Systems (YKB-02A).
In the device is mounted an optical-smoke fire detector type FD8030 for Conventional Systems or FD7130 for Addressable Systems.
In order to conrol the condition of the integrated fire detector, on the housing of the duct smoke detector is mounted an outboard LED Remote Indicator RI31.In case of smoke in the main air conduit, part of this smoke goes through the duct smoke detector and activates the fire detector. The latter sends signal to the Fire Control Panel and the outboard Remote indicator.
Tham khảo thêm các thiết bị báo cháy tự động liên quan: Tủ trung tâm báo cháy địa chỉ, đầu báo khói địa chỉ, đầu báo nhiệt địa chỉ, module giám sát, module điều khiển, Module định địa chỉ cho đầu báo thường, nút nhấn địa chỉ, chuông báo cháy, đèn báo cháy ngoài nhà Unipos, tủ hiển thị phụ UniposLiên hệ -
Diode chống nổ cho đầu báo cháy
Xem Catalogue
MTL7787+ là thiết bị chống nổ cho môi trường có nguy hiểm cháy nổ caos.
All MTL7700 Series barriers are based on the same simple principle. Each channel contains two stages of
pulse-tested Zener or forward-connected diodes and an ‘infallible’ terminating resistor. In the event of
an electrical fault in the safe area, the diodes limit the voltage that can reach the hazardous area and the
resistor limits the current. A fuse protects the the diodes, and the two stages of voltage limitation ensure
continued safety if either stage should fail. No active output-current limiting circuits are employed. The
MTL7787+ is certified ‘ia’ for all zones and ‘IIC’ for all explosive atmospheres.
Tham khảo thêm các thiết bị báo cháy tự động liên quan: Tủ trung tâm báo cháy địa chỉ, đầu báo khói địa chỉ, đầu báo nhiệt địa chỉ, module giám sát, module điều khiển, Module định địa chỉ cho đầu báo thường, nút nhấn địa chỉ, chuông báo cháy, đèn báo cháy ngoài nhà Unipos, tủ hiển thị phụ Unipos
Liên hệ -
Thiết bị chống sét cho hệ thống báo cháy
Xem Catalogue
Thiết bị chống sét DNP508 và DNP5082 được thiết kế để bảo vệ mạch điện, điện tử và các thiết bị trong hệ thống báo cháy. Có 2 dòng sản phẩm:- DNP508 - Để bảo vệ các thiết bị trong hệ thống báo cháy thông thường (dạng kênh vùng);
- DNP5082 - Để bảo vệ các thiết bị trong hệ thống báo cháy địa chỉ thuộc dòng sản phẩm IFS7002, do UniPOS sản xuất.
2.THÔNG SỐ KỸ THUẬT
DNP508 DNP5082 2.1. Nominal voltage 28V DC - 2.1.1. Signal Loop - 33V DC 2.1.2. Power Loop - 28V DC 2.2. Maximum current pulse IS 8/20 20 kA 2.3. Response time 1 ns 2.4. Maximum resultant voltage at IS8/20 45.7V - 2.4.1. Signal Loop IS 8/20 - 72.2V 2.4.2. Power Loop IS 8/20 - 53.3V 2.5. Operating temperature range from minus 10ºС to 60ºС 2.6. Storage temperature from minus 40ºС to 70ºС 2.7. Relative humidity resistance (92+3 )% at 40ºС
-22.8. Degree of protection IP40 2.9. Overall dimensions 162х120х72 mm 2.10. Weight 0,3 kg - STRUCTURE AND FUNCTIONALITY
- Structure
The cover is fixed by the base my means of four screws.3.2.Functionality
When lightning strikes, DNP508 limits the maximum voltage of the line to 150/180V, and the terminals of the Control Panel to 46V for DNP508 (and 72/53V for DNP5082).
4.INSTALLATION
Mount the base of DNP508 (DNP5082) to the wall by means of dowels and self- tapping screws.
Separate the cover from the base. Fix the base to the wall by dowels and wood screws. Then perform the electrical installation in accordance with item 4. Place the cover to the base and screw the four fixings.4.1.Connecting method (fig.1 DNP 508) (fig.2 DNP 5082)
- Connect the fire alarm lines (loops) to terminals FD.
- Connect terminals FS to the respective terminals of the Control Panel.
- Performing Installation:
- for lines / loops - by means of wire (0.8-2.5)mm2;
- for grounding - by means of wire (1.5-2.5)mm2 .
WARNING! For the reliable operation of the lightning protection unit, it is necessary to realize a secure electrical connection from the grounding terminals to the housing of the Control Panel. The housing of the Control Panel must be grounded to the power supply switchboard with a separate wire with minimum cross section 1.5 mm2. The supply switchboard must have a standard grounding.
When installing the lightning protection unit into a place, where the fire alarm lines are extended beyond the building, the grounding wire must be connected to the grounding bus of the building or a standard grounding to be made for that purpose.4.2.Satisfactory operation test in real conditions
Consecutively short each line(loop) for a while - The Control Panel must “FAULT CONDITION”.
5.SERVICE SCHEDULE
Procedure Periodicity 1. Inspection for visible physical damages weekly 2. Satisfactory operation test in real conditions monthly 3. Check and clean dust contamination every six months - WARRANTY
Tham khảo thêm các thiết bị báo cháy tự động liên quan: Tủ trung tâm báo cháy địa chỉ, đầu báo khói địa chỉ, đầu báo nhiệt địa chỉ, module giám sát, module điều khiển, Module định địa chỉ cho đầu báo thường, nút nhấn địa chỉ, chuông báo cháy, đèn báo cháy ngoài nhà Unipos, tủ hiển thị phụ UniposLiên hệ -
Nút nhấn khẩn cấp báo cháy FD3050
Xem catalogue
Tiêu chuẩn Châu Âu: EN54-11
Có đèn LED chỉ trạng thái
Có chìa khóa để thử (test)
Nguồn cấp: 12-30V DC
Độ nhạy: tiêu chuẩn EN54-5
Lớp bảo vệ: IP40
Kích thước: 90x90x44mm
Chất liệu: Nhựa ABS, màu đỏ
Nút nhấn khẩn cấp còn được gọi là nút ấn báo cháy hoặc nút ấn khẩn cấpLiên hệ -
Đầu báo khói quang FD8030
Nguồn cấp: 12 - 30 V DC A
Dòng trong tình trạng báo động (khi sử dụng với đế 3000 & 3000D): 8 - 25 mA
Độ nhạy: theo tiêu chuẩn EN 54-5
Lớp bảo vệ: IP43
Chất liệu: nhựa ABS, màu trắng
Vùng bảo vệ: vòng tròn D=10m, H=8mLiên hệ -
Đầu báo nhiệt cố định FD8010
Nguồn cấp: 12 - 30 V DC A
Dòng trong tình trạng báo động (khi sử dụng với đế 3000 & 3000D): 8 - 25 mA
Độ nhạy: theo tiêu chuẩn EN 54-5
Lớp bảo vệ: IP43
Chất liệu: nhựa ABS, màu trắng
Vùng bảo vệ: vòng tròn D=10m, H=8mLiên hệ -
Đầu báo nhiệt gia tăng FD8020
Nguồn cấp: 12 - 30 V DC A
Dòng trong tình trạng báo động (khi sử dụng với đế 3000 & 3000D): 8 - 25 mA
Độ nhạy: theo tiêu chuẩn EN 54-5
Lớp bảo vệ: IP43
Chất liệu: nhựa ABS, màu trắng
Vùng bảo vệ: vòng tròn D=10m, H=8mLiên hệ -
Đầu báo khói nhiệt kết hợp FD8060
Nguồn cấp: 12 - 30 V DC A
Dòng trong tình trạng báo động (khi sử dụng với đế 3000 & 3000D): 8 - 25 mA
Độ nhạy: theo tiêu chuẩn EN 54-5
Lớp bảo vệ: IP43
Chất liệu: nhựa ABS, màu trắng
Vùng bảo vệ: vòng tròn D=10m, H=8mLiên hệ -
Đầu báo lửa FD3040
Xem Catalogue
Nguồn cấp: 12 - 30 V DC A
Dòng trong tình trạng báo động (khi sử dụng với đế 3000 & 3000D): 8 - 25 mA
Độ nhạy: theo tiêu chuẩn EN 54-10
Lớp bảo vệ: IP40
Chất liệu: nhựa ABS, màu trắng
Vùng bảo vệ: góc nhìn 90 độ, phát hiện lửa từ khoảng cách 20 mét
Liên hệ -
Đèn báo phòng (đèn báo vị trí)
- Báo hiệu tại vị trí xảy ra cháy
Nguồn cấp: 5-30V
Dòng khi có tình trạng báo động: 40mA
Mạch kết nối: 2 dây
Lớp bảo vệ: IP40
Kích thước: 75x75x22mm
Đèn báo cháy RI31 thường được lắp đặt tại cửa các phòng kín trong các chung cư hoặc tòa nhà văn phòngLiên hệ